MUR605CT thru mur660ct 6 amp super fast glass passivated rectifier features maximum ratings operating temperature: -5 5 c to +1 50 c storage temperature: -5 5 c to +150 c microsemi catalog number device marking maximum recurrent peak reverse voltage maximum rms voltage maximum dc blocking voltage MUR605CT MUR605CT 50v 35v 50v mur610ct mur610ct 100v 70v 100v mur620ct mur620ct 200v 140v 200v mur640ct mur640ct 400v 280v 400v mur660ct mur660ct 600v 420v 600v electrical characteristics @ 25 c unless otherwise specified average forward current i f(av) 6 a t c = 130 c peak forward surge current i fsm 75a 8.3ms, half sine maximum forward voltage drop per element v f i fm = 3 a per element; t a = 25 c* maximum dc reverse current at rated dc blocking voltage i r 5.0u a 5 0 ua t j = 25 c t j = 100 c *pulse test: pulse width 300 m sec, duty cycle 1% inches mm
a .570 .620 14.48 15.75 b .380 .405 9.66 10.28 u ------ .050 ----- 1.27 c .160 .190 4.06 4.82 d .025 .035 0.64 0.89 f .142 .147 3.61 3.73 g .095 .105 2.42 2.66 h .110 .155 2.80 3.93 j .018 .025 0.46 0.64 k .500 .562 12.70 14.27 l .045 .060 1.14 1.52 q .100 .120 2.54 3.04 r .080 .110 2.04 2.79 s .045 .055 1.14 1.39 605ct-620ct 1 .25 v 640ct- 660ct . 975 v glass passivated chip superfast switching time for hight efficiency low reverse leakage current high surge capacity 605ct- 620 640ct 35ns 60ns maximum reverse recovery time t rr i f =8.0a, i rr =0.25a to-220ab 50 to 600 volts t .235 .255 5.97 6.48 g r b q h u l d c j k a f s t 1 3 4 2 n v p i n 1 . an o d e pin 2 . ca t hode pin 3. anode pin 4 . ca t hode v .045 ------ 1.15 ------- 660ct 75ns http://www.kersemi.com
MUR605CT thru mu660ct instantaneous reverse leakage current - microamperes versus percent of rated peak reverse voltage - volts average forward rectified current - amperes versus ambient temperature - c figure 3 forward derating curve 50 100 125 150 160 175 0 0 2 4 6 single phase, half wave 60hz resistive or inductive load amps c 8 12 16 instantaneous forward current - amperes versus instantaneous forward voltage - volts figure 1 typical forward characteristics volts 4 6 20 10 amps .2 1.2 .4 .6 .8 1.0 .01 .02 .04 .06 .1 .2 .4 .6 1 2 25 c 40 60 100 1.4 figure 2 typical reverse characteristics volts .4 .6 2 1 mamps 20 140 40 60 100 120 .001 .002 .00 4 .006 .01 .02 .04 .06 .1 .2 4 6 10 160 t j =25 c 1 100 4 0 25 50 75 8 figure 4 maximum non-repetitive forward surge current peak forward surge current - amperes versus number of cycles at 60hz - cycles amps cycles 2 6 10 20 60 80 40 00 100 125 150 640ct-660ct 605ct-620ct http://www.kersemi.com
|
